Rerelocating Power Steering Pulley sounds exceptionally easy and simple, however actually, once it concerns doing it in action, it is not that basic. Basically, you should remove and also reinstall the pulley-block via maximum treatment. If you are not a Car-guy and have nopoint to perform with parts and methods to settle your auto, then I would recommend you to consult a automobile technology. Tbelow are many type of misconceptions that Power steering pulley-block removal without a tool is actually not possible. But to your surprise, it is actually possible and also deserve to be done at your home itself.

You are watching: How to remove power steering pump pulley without puller

Here is an short article briefing you How to remove power steering pulley without a puller. Follow the procedures listed below, and you have the right to easily complete the process at your house likewise.

Pre-Removal essential steps:

Place your car on the ground level and park in traditional transmission.Let the engine cool, execute not begin working on the heated engine. Do not foracquire to apply the parking brake.Keep the hood of the vehicle open up. Keep the battery dislinked prior to the removal or installation of Power steering wheel.

How to Rerelocate Power Steering Pulley without Puller

Tip 1:

While replacing the power steering pulley, make certain that the major drive pulley is rerelocated and also then reinstalled. The remounted pulley has to be pressed into the input shaft for improving the functioning of the inner pump. The connection of the inner shaft and also pump allows the engine to carry the power from a serpentine belt to the power steering pump sheave.

Tip 2:

The removal tool can take approximately 12 inches in front of the pump. After rerelocating the tool, you deserve to clean and also rerelocate the pump that is a mounting bracket for adequate room. Once you have actually enough area to attach the removal tool in front of the pump. Fit the tool by making use of some force and also press to get a perfect position.

Tip 3:

To obtain an intimation of a wheel to begin, you will certainly hear a pop informing the tool is began now. You must continue this procedure until the pulley-block becomes totally free enough to pump input shaft. Make certain you warmth the pulley to around 120-130 degrees F and then reinstall the sheave.


Tip 4:

The installation of the pulley-block must be done in a clean, rust-complimentary shaft. If the shaft and also the pulley-block are not cleaned, then the installation process can end up being challenging and lengthy. Note: Do not lubricate the sheave or shaft through any kind of grease, water, or any liquid. 

If, by any chance, grease or oil is current, make certain to clean it before installation. Lubrication have the right to cause the wheel to slip and also result in failure installation.

Step 5:

As we desire the wheel to warm at 120-130 levels. Once we achieve the specific temperature, it is the perfect time to align the wheel onto the shaft. Now you need to spin the sheave till it ensures a square mount gently. Forming a square mount will start the alignment to form appropriately before any installation.

Tip 6:

Now it is time to rotate the pulley-block on and take the wobble out. This suggests that the wheel is square and perfect. Next off up, we will certainly attach the installation tool in front of the input shaft pump.

Tip 7:

With step 6, the installation will be completed. Now you have to tighten the collar versus the pulley-block. Aacquire continue to tighten the installation through a ratchet and wrenches. Make certain you have not left any type of loss areas.


Tip 8:

Continue to tighten the tool until the power steering pulley-block is thoabout installed. It needs to be fluburned together with the pump input shaft. Once you encertain that the wheel is completed flushed in addition to the shaft, below the installation is done.

See more: The Is Considered The Basic Unit Of Any Element S, And Atoms

Important Precautions

Never attempt to rerelocate or install a power steering pulley via the assist of a hammer.

Wuff! It’s done. It is tiring and also really tough, but once it’s done, your engine is going to job-related smoothly. Make certain you undergo each action carefully and store the necessary preadvises in mind. Also, the pre-removal steps are necessary as they are some procedures that must be done prior to operation any type of car-connected actions. I hope this article would have helped you to remove power steering wheel without pulley. See you shortly via one more impressive post.